Hm, well I don't have any glass here, we'd nee d to get some cut. I do have some 2mm aluminium sheets at 203mm x 330mm.<br>Roy<br><br><div class="gmail_quote">On 23 January 2012 23:38, Thomas Parry <span dir="ltr"><<a href="mailto:yrrapt@gmail.com">yrrapt@gmail.com</a>></span> wrote:<br>

<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">We could certainly have a go at making our own PCB heating bed. Will be<br>
pretty simple to do and there's hardy anything lost if it fails.<br>
<br>
Tom<br>
<div><div class="h5">On Jan 23, 2012 8:26 PM, "Blair Thompson" <<a href="mailto:mail@justblair.co.uk">mail@justblair.co.uk</a>> wrote:<br>
<br>
> As I understand it Clive. For glass the qualities that makes the<br>
> difference are:<br>
><br>
>  * It presents a nice flat surface for the plastic to adhere to.<br>
>  * It does not warp when heated<br>
>  * Its pretty light when compared to steel or 6mm thick machine aluminium<br>
>  * Its surface hard to damage when removing parts<br>
>  * Its cheap (£5 per 20cm^2)<br>
><br>
> The high insulation is actually one of it's downsides.  It takes longer to<br>
> heat up than aluminium, and as it does not conduct heat so well, it must be<br>
> heated evenly for both the quality of the print and to prevent the glass<br>
> cracking.  Some people put heater/thin alu/glass as a combination.<br>
><br>
> On 23/01/2012 18:51, Clive Mitchell wrote:<br>
><br>
>> I think glass is often used because it's a good balance between laying<br>
>> down the first plastic and then separating the finished object<br>
>> afterwards.  It's also a good insulator, so that allows the heating<br>
>> element to be placed in direct contact.<br>
>><br>
>> The PCB based heating plate looks neat.  By specifying a standard<br>
>> copper thickness and fine tuning the track width and length they seem<br>
>> to have come up with a very simple and consistent heating plate.<br>
>><br>
>> On 23 January 2012 17:45, Kieran Wyse<<a href="mailto:kieranwyse@gmail.com">kieranwyse@gmail.com</a>>  wrote:<br>
>><br>
>>> It is very likely we are going to make a heated bed( please forgive my<br>
>>> stupidity if this is not the top and bottom plates). Brian has suggested<br>
>>> he<br>
>>> may be able to get hold of some metal sheet but for best results, I have<br>
>>> read, that a glass plate on top is good.<br>
>>><br>
>>> I don't think a decision has been made but it is likely we will go the<br>
>>> thermistor route copper wire for the heat bed. If you had some lying<br>
>>> around<br>
>>> it would force us to make a decision:)<br>
>>><br>
>><br>
>><br>
>><br>
> -------------- next part --------------<br>
> An HTML attachment was scrubbed...<br>
</div></div>> URL: <<a href="http://www.electronclub.org/**pipermail/members/attachments/**" target="_blank">http://www.electronclub.org/**pipermail/members/attachments/**</a><br>
> 20120123/732af067/attachment.**html<<a href="http://www.electronclub.org/pipermail/members/attachments/20120123/732af067/attachment.html" target="_blank">http://www.electronclub.org/pipermail/members/attachments/20120123/732af067/attachment.html</a>><br>


> ><br>
> ______________________________**_________________<br>
> members mailing list<br>
> <a href="mailto:members@electronclub.org">members@electronclub.org</a><br>
> <a href="http://www.electronclub.org/**cgi-bin/mailman/listinfo/**members" target="_blank">http://www.electronclub.org/**cgi-bin/mailman/listinfo/**members</a><<a href="http://www.electronclub.org/cgi-bin/mailman/listinfo/members" target="_blank">http://www.electronclub.org/cgi-bin/mailman/listinfo/members</a>><br>


<div class="im">><br>
> Instructions for changing your mailing list settings:<br>
</div>> <a href="http://lists.electronclub.org/**emailhowto.html" target="_blank">http://lists.electronclub.org/**emailhowto.html</a><<a href="http://lists.electronclub.org/emailhowto.html" target="_blank">http://lists.electronclub.org/emailhowto.html</a>><br>


><br>
> Archive for this list:<br>
> <a href="http://lists.electronclub.org/**pipermail/members/" target="_blank">http://lists.electronclub.org/**pipermail/members/</a><<a href="http://lists.electronclub.org/pipermail/members/" target="_blank">http://lists.electronclub.org/pipermail/members/</a>><br>


<div class="im">><br>
-------------- next part --------------<br>
An HTML attachment was scrubbed...<br>
</div>URL: <<a href="http://www.electronclub.org/pipermail/members/attachments/20120123/99bf0409/attachment.html" target="_blank">http://www.electronclub.org/pipermail/members/attachments/20120123/99bf0409/attachment.html</a>><br>


<div class="HOEnZb"><div class="h5">_______________________________________________<br>
members mailing list<br>
<a href="mailto:members@electronclub.org">members@electronclub.org</a><br>
<a href="http://www.electronclub.org/cgi-bin/mailman/listinfo/members" target="_blank">http://www.electronclub.org/cgi-bin/mailman/listinfo/members</a><br>
<br>
Instructions for changing your mailing list settings:<br>
<a href="http://lists.electronclub.org/emailhowto.html" target="_blank">http://lists.electronclub.org/emailhowto.html</a><br>
<br>
Archive for this list:<br>
<a href="http://lists.electronclub.org/pipermail/members/" target="_blank">http://lists.electronclub.org/pipermail/members/</a><br>
</div></div></blockquote></div><br>